我在附件中进行了配置。
I made configuration in attach.
My Old桌面运行Modbus Simulator将值发送到S7 1212C(假设发送一个“实际温度室”)
My Old desktop running Modbus Simulator to send value to S7 1212C (Let's say sending an "Actual Temperature Room")
我的新笔记本电脑可以读取从桌面发送的数据,并可以通过西门子自己的Web服务器页面(192.168.xx.xx)将值写入S7 1212C(比如写入“最高温度设定点”)。
My new laptop can Read data that send from my desktop and can write value to S7 1212C (Let's say writing a "Maximum Temperature Set Point") via Siemens's own Web Server Page (192.168.xx.xx).
我刚刚使用了一个动态浏览器来访问西门子自己的web服务器(Chrome)。
I just used ordynary browser to access Siemens's own web server (Chrome).
它工作完美无误。“我的桌面”还可以同时读取两个值(实际值和设定值),也可以使用web浏览器(Chrome或其他)访问西门子自己的web服务器。
It works flawlessly without a glitch. My Desktop can also read both value (Actual and Setpoint) at the same time can also access to Siemens's own web server using web browser (Chrome or other).
问题是。我只能在旧桌面上运行Modbus模拟器。
The problem is. I can only running Modbus Simulator in my old Desktop.
当我尝试在笔记本电脑中运行Modbus模拟器时,Modbus连接断开(无连接)。
When I try to run Modbus Simulator in my Laptop, the Modbus connection is out (no connection).
即使我仍然可以通过台式机或笔记本电脑上的浏览器,或通过ping 192.168.xx访问西门子自己的服务器。xx,S7 1212C仍然响应正常。
Even I can still reach Siemens's own server _ from my browser in desktop or laptop, or by ping 192.168.xx.xx, the S7 1212C still responded normally.
如果Modbus连接已断开,我将无法再访问,即使我将Modbus模拟器运行回我的桌面。我必须先重置它(关闭它),然后它才能正常工作。
If the Modbus connection is already out, I cannot access anymore, even I running Modbus Simulator back to my Desktop. I have to reset it first (turn it off), and then it works normaly.
有什么建议吗?
Any suggestion?
你好
Hello,
误导有关PC和笔记本IP的重要信息。若其中一个客户机正确地从服务器断开连接,然后第二个客户机连接到服务器,则看不到问题。两者必须使用相同的服务器IP和端口值。所以在我看来,问题在于仍未正确断开与服务器的连接或IP/端口的连接。
mising important infos about PC and Notebook IPs. Don't see problem if one of Client is correctly disconnect from server and then second Client cpnnect to Server. Both must use same IP and Port value of Server. So in my opinion problem is with still not correctly disconnection from Server or IP/Port problem.
您正在使用哪个MB Sim
Which MB Sim you're using?
... VM memory is then read in as a data block.来自固件FS04的LOGO!也是MODBUS TCP/IP。 From firmware FS04 the LOGO! also MODBUS TCP / IP.您将使用哪个PLC用LOGO更改数据! ? With which PLC will you Change data with the LOGO! ?推荐答案3实际上,我不会放几个徽标,...
...线系统LOGO!只能使用S7协议和0BA8.FS04(或更新版本)附加Modbus的以太网TCP/IP。 If the with "Output: CAN" CAN bus is meant, then the sensor does not go to the LOGO!. The LOGO! can not use a fieldbus, Profibus or similar bus systems.The LOGO! can only Ethernet TCP/IP with the...
...默生DCS。这是我们第一次想用这种方法。我们之前测试过Modbus。但现在我们想从Modbus迁移到TCP/IP。 We have 4 S7-400FH PLCs that we want to connect them to Emerson DCS using TCP/IP. It's the first time that we want to use this way. we tested Modbus before. but now we wa...
... methods and when we can use each one ? - Profibus. - Profibus. -串行ModBus。 - serial ModBus.-TCP/IP ModBus。 - TCP/IP ModBus. - Mlink. - Mlink. 感谢您的支持 Appreciate your support 推荐答案2您好,正在加载; Hello loading;你到底在找什么?网络的硬件和软...
...attached configuration.我的疑问: My Doubts:1.网关是否可以使用MODBUS TCP/IP协议? 1.MODBUS TCP/IP protocol is possible for gateway?2.是否有任何参考项目可供任何人使用? 2.Is there any reference project available with anybody?3.此通信需要什么额外硬件? 3.Wh...
问题描述你好 hi我正在使用modbus主/从通信。距离更远。我需要放光缆。 I am using modbus master/slave communcation. Distance is more. I need to put fiber obtic cable.请告诉我可以将modbus转换为光纤的模块的详细信息,反之亦然。 Please let me know the d...
...tomer wants to provide the S7-400H system with remote I/O communication 在Modbus以太网TCP/IP或以太网TCP/IP上。 on Modbus Ethernet TCP/IP or Ethernet TCP/IP.是否有可能或转换在以太网TCP/IP上建立通信? Is there any possibility or conversion to establish the communication on ...
...10.63.100可以将我的程序员设置在192上,但路由器不允许我访问该网络。 To set my programmer on the 192 is possible but the router would not allow me to reach that net.推荐答案4哦 Oh在这种情况下,你不能连接。 You can't connect in such case.我告诉你的是NA...
...统都正确定义了默认网关。如果未定义默认网关,则可以访问本地系统,但不能访问位于路由器后面的系统。在服务器上使用ping命令可以帮助查看是否可以访问远程系统。 2) If the connections between server and S7-systems are based on TCP/IP, ...
...S7300或400系统中,是否有任何可用的模块通过以太网工作Modbus。当前CP341模块Modbus Serial只能与RS232、422485一起工作。 in S7300 or 400 system, is there any module available which works Modbus over ethernet. The current CP341 module Modbus Serial work only with RS232,...
如果觉得我的文章对您有用,请随意打赏。你的支持将鼓励我继续创作!